Posts

Water Level Indicator For Tank - Iot Fiers

Water Level Indicator Introduction A water-level marker is an electronic circuit device that transfers data back to the control board to show whether a waterway has a high or low water level. Some water level markers utilize a mix of test sensors or changes to detect water levels. The reason for a water level pointer is to measure and oversee water levels in a water tank. The control board can likewise be customized to consequently turn on the water once levels get excessively low and top off the water back to the sufficient level. Water level indicator definition : A water level indicator is a system that relays information back to a control panel to indicate whether a body of water has a high or low water level. Some water level indicators use a combination of probe sensors or float switches to sense water levels. “The Water Level Indicator employs a simple mechanism to detect and indicate the water level in an overhead tank or any other water container.” according to El
Post a Comment
Read more

Automatic water-level controller circuit -Iot Fiers

  Here is a simple, automatic water-level controller for overhead tanks that switches on/off the pump motor when water in the tank goes below/above the minimum/maximum level. The water level is sensed by two floats to operate the switches for controlling the pump motor. Automatic water-level controller circuit Each sensor's float is suspended from above using an aluminum rod. This arrangement is encased in a PVC pipe and fixed vertically on the inside wall of the water tank. Such sensors are more reliable than induction-type sensors. Sensor 1 senses the minimum water level, while sensor 2 senses the maximum water level (see the figure Leaf switches S1 and S2 (used in tape recorders) are fixed at the top of the sensor units such that when the floats are lifted, the attached 5 mm dia. (approx.) aluminum rods push the moving contacts (P1 and P2) of leaf switches S1 and S2 from normally closed (N/C) position to normally open (N/O) position. Similarly, when the water level go
Post a Comment
Read more

Automatic Sanitizer and soap Dispenser in Delhi - Iot Fiers

 The safest soap dispenser, completely contactless, automatic and super saver in soap consumption. The bacteria and viruses get transmitted through the touchpoints. Every time someone uses a normal soap dispenser, they leave traces of microorganisms on the plunger from their dirty and contaminated hands. Touchless Soap Dispenser emits soap foam the moment a hand or an object is brought under its spout, making it completely safe for use at home, office, factory or any public place. Use it with any dish-wash or hand-wash liquid and enjoy the magic. Dilute the liquid soap 5 to 10 times, depending upon its viscosity, while putting it in. Touchless also makes the use of soap so much more efficient. The foam spreads better and uses 5 times lesser soap for the same application as liquid soap from normal dispensers. For more information Automatic Water Level Controller Working Principle
Post a Comment
Read more

Automatic Water Level Controller Working Principle

Are you searching Google for “ Automatic Water Level Controller Working Principle ” in hopes of trying to understand what a water level controller does ? If so, this guide will help. What Is An Automatic Water Level Controller?   Automatic water level controllers D are a product that was created to automatically control a motor, which helps to ensure a constant reserve of water in a storage tank. These automatic water level controllers are used to automatically fill the over-head tank when it starts or has become empty, as well as monitor the water level in it. Automatic water level controllers switch the motor on whenever the water level drops below a certain level and shuts the motor off when the water rises well above a fixed level . The motor will also switch off when the sump water is exhausted before it fills the over-head tank, or if the pump is running dry, as well as maintains voltage fluctuations. These are state of the art advanced, digital technology microc
Post a Comment
Read more

Water level controller in Delhi - Iot Fiers

  Water level controller in Delhi This is a circuit for water level controller is based on transistors and relays. The circuit automatically switches on the pump when water is low in the tank and switches the pump off when water reaches a predetermined mark. - In most houses, water is first stored in an underground tank (UGT) and from there it is pumped up to the overhead tank (OHT) located on the roof. People generally switch on the pump when their taps go dry and switch off the pump when the overhead tank starts overflowing. This results in the unnecessary wastage and sometimes non-availability of water in the case of emergency. This water-level controller circuit makes this system automatic. It switches on the pump when the water level in the overhead tank goes low and switches it off as soon as the water level reaches a pre-determined level. It also prevents ‘dry run’ of the pump in case water level in underground tank goes below suction level. In this water-level cont
Post a Comment
Read more